Question 1

A storage network engineer is implementing SAN telemetry for a SAN infrastructure using Cisco DCNM for SAN. Which command is used to check the session status for telemetry operation?
A) show telemetry pipeline stats
B) show telemetry transport
C) show telemetry control stats
D) show analytics system-load

Accepted Answer

The command "show telemetry transport" is used to check the session status for telemetry operation in a SAN infrastructure using Cisco DCNM.

Question 2

Refer to the exhibit.  The san-user must configure FSPF on the VSAN 500, but fails. An operator with network administrative rights must authorize the san-user to perform this work. Which configuration must the operator apply?
A) MDS-A(config)# role name sangroup MDS-A(config-role)# no rule 2 MDS-A(config)# role name sangroup MDS-A(config-role)# no rule 2
B) MDS-A(config-role)# rule 4 permit config feature fspf rule 4 permit config feature fspf
C) MDS-A(config-role)# rule 2 permit config feature vsan rule 2 permit config feature vsan
D) MDS-A(config-role)# vsan policy deny MDS-A(config-role-vsan)# permit vsan 500 vsan policy deny MDS-A(config-role-vsan)# permit vsan 500

Accepted Answer

The answer of Refer to the exhibit.  The san-user...

Question 3

Refer to the exhibit.  A user who is logged in as an operator cannot update the zoneset. What is the cause of this issue?
A) The fabric is locked by admin on switch-2.
B) Hard zoning is enabled.
C) Merge control is disabled.
D) The switch has a conflicting domain ID.
E) The fabric is locked by admin on another switch.

Accepted Answer

The answer of Refer to the exhibit.  A user...

Question 4

Refer to the exhibit.  What is the result of the configuration?
A) No-drop CoS values are advertised by the DCBX.
B) LFC is prioritized over PFC on Ethernet 1/10.
C) PFC operates on Ethernet 1/10 regardless of the capability of the peer.
D) PFC fails to operate properly unless LFC is disabled on Ethernet 1/10.

Accepted Answer

The answer of Refer to the exhibit.  What is...

Question 5

Refer to the exhibit.  Device alias information must be merged for two fabrics. Which setting must match on both fabrics before the merge can be performed successfully?
A) device-alias mode
B) session
C) qos
D) smart-zoning

Accepted Answer

The answer of Refer to the exhibit.  Device alias...

Question 6

Which configuration is needed to enable manual ESP mode for Fibre Channel TrustSec on Cisco MDS switches?
A) MDS(config)# interface fc 1/1 MDS(config-if)# fcsp esp manual MDS(config)# interface fc 1/1 MDS(config-if)# fcsp esp manual
B) MDS(config)# fcsp esp manual
C) MDS(config-if)# fcsp mode gcm MDS(config-if-fcsp)# fcsp esp manual fcsp mode gcm MDS(config-if-fcsp)#
D) MDS(config-if-fcsp)# mode gcm MDS(config-if-fcsp)# mode gcm

Accepted Answer

The correct configuration involves entering the interface configuration mode and then enabling manual ESP mode with the command `fcsp esp manual`.

Question 7

Which benefit of upgrading to the Cisco DCNM server-based advanced feature license for a Cisco MDS switch is correct?
A) The license can be reassigned when a switch is replaced with a newer version within the same product family.
B) The license can be assigned to either server MAC address or switch serial number.
C) An unlimited number of devices can be added to the list of licensed devices.
D) The license can be reassigned when the switch is replaced with a Cisco Nexus switch.

Accepted Answer

The license can be reassigned when a switch is replaced with a newer version within the same product family, allowing for flexibility in hardware upgrades.

Question 8

Refer to the exhibit.  What is the result of merging the fabric?
A) The merged fabric IVR VSAN topology is set to activate.
B) The merged fabric has NAT enabled.
C) The merge is invalid.
D) The merged fabric contains only service group Group1.

Accepted Answer

The answer of Refer to the exhibit.  What is...

Question 9

Refer to the exhibits.   A storage network engineer activates a zoneset on MDS-A and verifies the successful activation ( Exhibit 1 ). The engineer is then notified that there is a SAN outage ( Exhibit 2 ) What is the cause of the outage?
A) Another network engineer activated zoneset ZoneSetMDS-B-VSAN100 on MDS-A.
B) Another network engineer issued the zone mode enhanced vsan 100 command on another switch in the fabric. Another network engineer issued the zone mode enhanced vsan 100 command on another switch in the fabric.
C) Another network engineer activated the zoneset ZoneSetMDS-B-VSAN100 command on another switch in the fabric. Another network engineer activated the zoneset ZoneSetMDS-B-VSAN100
D) Another network engineer issued the zone default-zone permit vsan 100 command on another switch in the fabric. zone default-zone permit vsan 100 command on another switch in the fabric.

Accepted Answer

The answer of Refer to the exhibits.   A...

Question 10

A storage administrator manually configures a storage switch to use a new static domain ID. After issuing an fcdomain restart vsan 1 command, the administrator sees that the switch is still using the existing domain ID. What is the reason why the configuration is not working?
A) Static domain IDs apply only after a switch is rebooted.
B) The disruptive keyword was not used on the command.
C) Build fabric notifications were not sent to the other switches.
D) Domain manager fast restart is not enabled on the switch.

Accepted Answer

Static domain IDs apply only after a switch is rebooted.

Question 11

A storage administrator is upgrading Cisco NX-OS on a Cisco MDS switch. The administrator performs an ISSU upgrade following the configuration guide. While the install is proceeding, the administrator connects a new server to the switch, which cannot access storage. The existing servers continue to operate properly through the switch. Why is the new server failing to connect?
A) The fabric data plane resets as part of the upgrade process.
B) The new server is unable to log in to the fabric to receive an FC-ID.
C) The upgrade process disables any currently unused ports.
D) The zoning database is locked during the upgrade process.

Accepted Answer

The answer of A storage administrator is upgrading Cisco NX-OS...

Question 12

Which action must be performed to deactivate a VSAN without losing its configuration?
A) Isolate it.
B) Delete it.
C) Rename it.
D) Suspend it.

Accepted Answer

Suspending a VSAN deactivates it without losing its configuration, allowing it to be reactivated later with the same settings.

Question 13

A storage engineer is troubleshooting a Cisco MDS switch upgrade issue. What prevents the completion of a non-disruptive upgrade?
A) The Fibre Channel host initiator is connected.
B) The Fibre Channel storage target is connected.
C) The Cisco Fabric Services operation in progress.
D) The Fibre Channel and FCoE storage targets are connected.

Accepted Answer

The answer of A storage engineer is troubleshooting a Cisco...

Question 14

Refer to the exhibit.  A network engineer must configure the SAN telemetry streaming feature to stream statistics form a Cisco MDS 9000 Series Switch to two external receivers with the IP addresses 192.168.1.4 and 192.168.1.5. Which two configurations accomplish this configuration? (Choose two.)
A) Add IP address 192.168.1.5 port 50005 protocol gRPC encoding GPB under destination-group 100.
B) Add IP address 192.168.1.5 port 50005 protocol gRPC encoding GPB under destination-group 300.
C) Add dst-grp 200 under subscription 100.
D) Add dst-grp 300 under subscription 200.
E) Add dst-grp 100 under subscription 200.

Accepted Answer

The answer of Refer to the exhibit.  A network...

Question 15

Two stable fabrics have overlapping domains. After a switch from the first domain is joined to a switch from the second domain, both switches become isolated. What caused the problem?
A) The autoreconfigure option is disabled on both switches.
B) The autoreconfigure option is enabled on both switches.
C) The rcf-reject option is enabled on the interfaces.
D) The rcf-reject option is disabled on the interfaces.

Accepted Answer

The autoreconfigure option is disabled on both switches. When the autoreconfigure option is disabled, the switches will not automatically reconfigure their ports when a link is added or removed. This can cause the switches to become isolated if a link is broken.

Question 16

A storage administrator is connecting two previously configured switches to make a single fabric. When the E Ports are connected, the administrator sees a ZONE MERGE FAILURE message referring to the zoneset for VSAN 10 on each switch. Which command should the administrator use to allow these switches to work together?
A) zoneset import interface fc1/1 vsan 10
B) zoneset distribute full vsan 10
C) zoneset overwrite-control vsan 10
D) zoneset copy active-zoneset full-zoneset

Accepted Answer

The answer of A storage administrator is connecting two previously...

Exam 20: Implementing Cisco Application Centric Infrastructure - Advanced

A storage network engineer is implementing SAN telemetry for a SAN infrastructure using Cisco DCNM for SAN. Which command is used to check the session status for telemetry operation?

Refer to the exhibit. The san-user must configure FSPF on the VSAN 500, but fails. An operator with network administrative rights must authorize the san-user to perform this work. Which configuration must the operator apply?

Refer to the exhibit. A user who is logged in as an operator cannot update the zoneset. What is the cause of this issue?

Refer to the exhibit. What is the result of the configuration?

Refer to the exhibit. Device alias information must be merged for two fabrics. Which setting must match on both fabrics before the merge can be performed successfully?

Which configuration is needed to enable manual ESP mode for Fibre Channel TrustSec on Cisco MDS switches?

Which benefit of upgrading to the Cisco DCNM server-based advanced feature license for a Cisco MDS switch is correct?

Refer to the exhibit. What is the result of merging the fabric?

Refer to the exhibits. A storage network engineer activates a zoneset on MDS-A and verifies the successful activation ( Exhibit 1 ) . The engineer is then notified that there is a SAN outage ( Exhibit 2 ) What is the cause of the outage?

A storage administrator manually configures a storage switch to use a new static domain ID. After issuing an fcdomain restart vsan 1 command, the administrator sees that the switch is still using the existing domain ID. What is the reason why the configuration is not working?

Which action must be performed to deactivate a VSAN without losing its configuration?

A storage engineer is troubleshooting a Cisco MDS switch upgrade issue. What prevents the completion of a non-disruptive upgrade?

Refer to the exhibit. A network engineer must configure the SAN telemetry streaming feature to stream statistics form a Cisco MDS 9000 Series Switch to two external receivers with the IP addresses 192.168.1.4 and 192.168.1.5. Which two configurations accomplish this configuration? (Choose two.)

Two stable fabrics have overlapping domains. After a switch from the first domain is joined to a switch from the second domain, both switches become isolated. What caused the problem?