Question 1

Disassembly of a Ford 6R60 overdrive clutch is being discussed. Technician A says to mark the snap ring opening before removing the snap ring. Technician B says to pry only 180° from the snap ring opening mark or the forward clutch housing will be destroyed. Who is correct?

Accepted Answer

Marking the snap ring opening helps in reassembly, and prying 180° from the snap ring opening prevents damage to the forward clutch housing.

Question 2

After reassembling the overdrive clutch assembly for a Ford 6R60 transmission, a dial indicator is set up on the pressure plate of the clutch assembly and two readings are taken 180° from one another. What is the acceptable clutch pack clearance when an average of these two measurements is calculated?

Accepted Answer

The acceptable clutch pack clearance for a Ford 6R60 transmission is typically measured in inches, and the range of 0.019" - 0.035" is the correct specification for this clearance.

Question 3

When rebuilding the forward clutch of a Ford 6R60 transmission, a paint pen should be used to draw a line between the forward clutch drum and the __________.

Accepted Answer

The answer of When rebuilding the forward clutch of a...

Question 4

After reassembling the forward clutch assembly of a Ford 6R60 transmission, a dial indicator is set up on the pressure plate of the clutch assembly and two readings are taken 180° apart. What is the acceptable clutch pack clearance when an average of these two measurements is calculated?

Accepted Answer

The acceptable clutch pack clearance for a Ford 6R60 transmission is typically measured in millimeters, and the range of 0.48 mm to 0.88 mm is the correct specification.

Question 5

What special tool is required to release the retaining ring that holds the carrier and the sun gear into the forward clutch on a Ford 6R60 transmission?

Accepted Answer

The answer of What special tool is required to release...

Question 6

When installing the forward clutch onto the overdrive clutch of a Ford 6R60 transmission, the new snap ring should be installed about __________ away from the original snap ring position.

Accepted Answer

The answer of When installing the forward clutch onto the...

Question 7

The direct clutch assembly on a Ford 6R60 is being discussed. Technician A says that new seals should be installed on the direct clutch piston and the balance piston. Technician B says that transmission fluid should be used to lubricate the new seals before assembly. Who is correct?

Accepted Answer

The answer of The direct clutch assembly on a Ford...

Question 8

After reassembling the intermediate clutch assembly of a Ford 6R60 transmission, a dial indicator is set up on the pressure plate of the clutch assembly and two readings are taken 180° apart. What is the acceptable clutch pack clearance when an average of these two measurements is calculated?

Accepted Answer

The acceptable clutch pack clearance for a Ford 6R60 transmission is between 0.019" and 0.051".

Question 9

During assembly of the 6R60 transmission, the service procedure states to measure the thickness of the low/reverse clutch pack and record the measurement. What components are included in that measurement?

Accepted Answer

The low/reverse clutch pack consists of friction plates, steel plates, and cushion springs. The pressure plate is not included in the measurement.

Question 10

After installing the low/reverse clutch pack into the transmission of a Ford 6R60 transmission, the intermediate support housing should be installed. The support tabs for the housing and the snap ring ends should be at the __________ and the __________ positions.

Accepted Answer

The answer of After installing the low/reverse clutch pack into...

Question 11

The 6R60 transmission does not contain any bands, servos, or dog clutches.

Accepted Answer

The 6R60 transmission, used in some Ford vehicles, is a fully automatic transmission that uses a planetary gear set and does not contain bands, servos, or dog clutches.

Question 12

The Ford 6R60 transmission and the ZF6HP26 are the same basic transmissions with some minor component differences.

Accepted Answer

The Ford 6R60 and the ZF6HP26 are both based on the same design, with the 6R60 being a version of the ZF6HP26 adapted for Ford vehicles, featuring some minor differences in components and tuning.

Question 13

Technician A says that the 6R60 transmission has a short dipstick underneath the fill plug. Technician B says that the transmission fluid level of 6R60 transmission can only be checked with a scan tool. Who is correct?

Accepted Answer

The answer of Technician A says that the 6R60 transmission...

Question 14

The 6R60 transmission uses a single Lepellitier planetary gear set.

Accepted Answer

The 6R60 transmission uses a single Lepellitier planetary gear set.

Question 15

Technician A says that the 6R60 transmission has six forward gears and one reverse. Technician B says that six multidisc clutches are used in this transmission. Who is correct?

Accepted Answer

The answer of Technician A says that the 6R60 transmission...

Question 16

Technician A says that some heavy-duty versions of the 6R60 transmission utilizes a one-way roller clutch to help with engine braking. Technician B says that the 6R80 is a heavy-duty versions of the 6R60 transmission. Who is correct?

Accepted Answer

The 6R80 is indeed a heavy-duty version of the 6R60 transmission, and some versions of these transmissions do utilize a one-way roller clutch for engine braking.

Question 17

Technician A says that all pre-2011 transmissions will have a TCM mounted to the transmission valve body. Technician B says that all transmissions are controlled by the PCM, regardless of the year. Who is correct?

Accepted Answer

Technician A is correct because all pre-2011 transmissions have a TCM mounted to the transmission valve body.

Question 18

The 6R60 transmission has seven shift solenoids.

Accepted Answer

The 6R60 transmission typically has six shift solenoids, not seven.

Question 19

Technician A says that all seven shift solenoids are variable force solenoids. Technician B says that all seven shift solenoids are on/off type solenoids. Who is correct?

Accepted Answer

Shift solenoids can be either variable force or on/off type, but not all seven solenoids are exclusively one type.

Question 20

The on/off solenoid should have a resistance of 10.5 ohms at room temperature.

Accepted Answer

The question states that the on/off solenoid should have a resistance of 10.5 ohms at room temperature.

Quiz 27: Ford 6r60 Zf6hp26

Disassembly of a Ford 6R60 overdrive clutch is being discussed. Technician A says to mark the snap ring opening before removing the snap ring. Technician B says to pry only 180° from the snap ring opening mark or the forward clutch housing will be destroyed. Who is correct?

When rebuilding the forward clutch of a Ford 6R60 transmission, a paint pen should be used to draw a line between the forward clutch drum and the __________.

After reassembling the forward clutch assembly of a Ford 6R60 transmission, a dial indicator is set up on the pressure plate of the clutch assembly and two readings are taken 180° apart. What is the acceptable clutch pack clearance when an average of these two measurements is calculated?

What special tool is required to release the retaining ring that holds the carrier and the sun gear into the forward clutch on a Ford 6R60 transmission?

When installing the forward clutch onto the overdrive clutch of a Ford 6R60 transmission, the new snap ring should be installed about __________ away from the original snap ring position.

The direct clutch assembly on a Ford 6R60 is being discussed. Technician A says that new seals should be installed on the direct clutch piston and the balance piston. Technician B says that transmission fluid should be used to lubricate the new seals before assembly. Who is correct?

After reassembling the intermediate clutch assembly of a Ford 6R60 transmission, a dial indicator is set up on the pressure plate of the clutch assembly and two readings are taken 180° apart. What is the acceptable clutch pack clearance when an average of these two measurements is calculated?

During assembly of the 6R60 transmission, the service procedure states to measure the thickness of the low/reverse clutch pack and record the measurement. What components are included in that measurement?

After installing the low/reverse clutch pack into the transmission of a Ford 6R60 transmission, the intermediate support housing should be installed. The support tabs for the housing and the snap ring ends should be at the and the positions.

The 6R60 transmission does not contain any bands, servos, or dog clutches.

The Ford 6R60 transmission and the ZF6HP26 are the same basic transmissions with some minor component differences.

Technician A says that the 6R60 transmission has a short dipstick underneath the fill plug. Technician B says that the transmission fluid level of 6R60 transmission can only be checked with a scan tool. Who is correct?

The 6R60 transmission uses a single Lepellitier planetary gear set.

Technician A says that the 6R60 transmission has six forward gears and one reverse. Technician B says that six multidisc clutches are used in this transmission. Who is correct?

Technician A says that some heavy-duty versions of the 6R60 transmission utilizes a one-way roller clutch to help with engine braking. Technician B says that the 6R80 is a heavy-duty versions of the 6R60 transmission. Who is correct?

Technician A says that all pre-2011 transmissions will have a TCM mounted to the transmission valve body. Technician B says that all transmissions are controlled by the PCM, regardless of the year. Who is correct?

The 6R60 transmission has seven shift solenoids.

Technician A says that all seven shift solenoids are variable force solenoids. Technician B says that all seven shift solenoids are on/off type solenoids. Who is correct?

The on/off solenoid should have a resistance of 10.5 ohms at room temperature.