Question 1

The ____________________ directs fluid flow from the turbine back to the impeller.

Accepted Answer

The answer of The ____________________ directs fluid flow from the...

Question 2

A(n)____________________ uses two gears to generate fluid pressure, not crescent.

Accepted Answer

The answer of A(n)____________________ uses two gears to generate fluid...

Question 3

​While discussing a positive-displacement gear type pump: Technician A says use a straight edge and feeler gauge to check gear side clearance. Technician B says normally the maximum clearance is 0.15 inch. Who is correct?

Accepted Answer

Both A and B are correct because a straight edge and feeler gauge are used to check gear side clearance, and the maximum clearance is typically 0.15 inches.

Question 4

____________________ refers to cycles per second.

Accepted Answer

The answer of ____________________ refers to cycles per second....

Question 5

A(n)_________________________ uses ATF as a medium to transfer engine torque.

Accepted Answer

The answer of A(n)_________________________ uses ATF as a medium to...

Question 6

A(n)____________________ uses an inner and outer rotor to generate pressure.

Accepted Answer

The answer of A(n)____________________ uses an inner and outer rotor...

Question 7

____________________ occurs when the fluid path is in the same circular direction as the rotation of the impeller.

Accepted Answer

The answer of ____________________ occurs when the fluid path is...

Question 8

​Technician A says a cooler located in the radiator can be replaced by a radiator shop if necessary. Technician B says if an external cooler is plugged it may make sense to replace it. Who is correct?

Accepted Answer

Technician A is correct because a cooler located in the radiator can be replaced by a radiator shop. Technician B is also correct because if an external cooler is plugged, it may make sense to replace it instead of trying to clean or repair it. Therefore, both technicians are correct.

Question 9

​Technician A says a shudder after the converter clutch engages could be caused by a cracked spark plug. Technician B says a transmission fluid change may fix a TCC shudder. Who is correct?

Accepted Answer

A cracked spark plug can cause engine misfires that mimic a TCC shudder, and changing the transmission fluid can address issues within the transmission that cause a TCC shudder.

Question 10

The ____________________ allows partial engagement of the converter clutch.

Accepted Answer

The answer of The ____________________ allows partial engagement of the...

Question 11

____________________ allows partial and full engagement of the TCC.

Accepted Answer

The answer of ____________________ allows partial and full engagement of...

Question 12

The ____________________ are springs located in the damper assembly.

Accepted Answer

The answer of The ____________________ are springs located in the...

Question 13

____________________ direct vortex flow to provide smooth turbulence-free fluid flow.

Accepted Answer

The answer of ____________________ direct vortex flow to provide smooth...

Question 14

​ Vane-type pumps are ____________________ whose output can be reduced when  high fluid pressures are not necessary.

Accepted Answer

The answer of ​ Vane-type pumps are ____________________ whose output...

Question 15

A(n)____________________ produces a fixed amount of fluid flow for each shaft rotation.

Accepted Answer

The answer of A(n)____________________ produces a fixed amount of fluid...

Question 16

____________________ is a type of pump that uses two gears.

Accepted Answer

The answer of ____________________ is a type of pump that...

Question 17

Technician A says that a dual-stage positive displacement oil pump, such as the design used by some Chrysler transmissions, allows the pump to deliver the pressure and fluid flow of a large displacement pump at high engine speeds. Technician B says that the dual stage pump delivers the pressure and fluid flow of a large displacement pump at lower engine speeds. Who is correct?

Accepted Answer

A dual-stage positive displacement oil pump is designed to provide the benefits of a large displacement pump at lower engine speeds, as stated by Technician B.

Question 18

A(n)____________________ is part of the clutch plate assembly that cushions clutch engagement.

Accepted Answer

The answer of A(n)____________________ is part of the clutch plate...

Question 19

A(n)____________________ prevents the clutch from engagement until the transmission or transaxle is in third gear.

Accepted Answer

The answer of A(n)____________________ prevents the clutch from engagement until...

Question 20

____________________ is fluid flow circulating between the impeller and the turbine.

Accepted Answer

The answer of ____________________ is fluid flow circulating between the...

Quiz 6: Torque Converters and Oil Pumps