Deck 3: Basic Tools and Precision Measuring

Question 1

Some tools are ________, so seek assistance if required, and use correct manual handling techniques when using tools.

A) Heavy
B) Easy to handle
C) Both A and B
D) Neither A nor B

Answer 1

A

Question 2

A screwdriver is designed to ________.

A) Be used as a hammer
B) Tighten and loosen screws
C) Provide leverage on sockets
D) Be used as a chisel

Answer 2

B

Question 3

Hand tools extend our ability to perform fundamental tasks such as:

A) gripping.
B) turning.
C) tightening.
D) All of the answers listed

Answer 3

D

Question 4

Technician A states that you should inspect tools prior to use to ensure they are in good working order. Technician B states that you should use tools to complete a task while ensuring manufacturer and shop procedures are followed. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 5

An example of a _______ would be physically securing a broken, unsafe, or out-of-service tool so that it cannot be used by anyone.

A) Lockout
B) Tag-out
C) Lockout/tag-out
D) None of the above

Question 6

An example of a tag-out would be affixing a(n) _________ to a piece of faulty equipment that describes the fault found in that equipment, includes the name of the person who found the fault, lists the date that the fault was found, and warns not to use the equipment.

A) Clear label
B) Obvious label
C) Bright red label
D) Both A and B

Question 7

_______ is an umbrella term that describes a set of safety practices and procedures that are intended to reduce the risk of technicians inadvertently using tools, equipment, or materials that have been determined to be unsafe, or potentially unsafe or that are in the process of being serviced.

A) Lock down/keep Away
B) Lockout/tagout
C) Lock in/don't use
D) None of the answers listed

Question 8

A fault is found with a piece of diagnostic equipment. What needs to be done?

A) Affix a clear and obvious label with details of the fault.
B) Keep aside the equipment for others to use.
C) Use the equipment till it completely breaks down.
D) Discard it.

Question 9

Which of the following problems would warrant a log-out/tag-out procedure of a vital piece of shop equipment?

A) Tool could is broken.
B) Tool is out of warranty.
C) Tool is unsafe.
D) Both A and C

Question 10

An automotive shop will usually have a selection of tools available for use, which includes:

A) specialized manufacturer tools.
B) high-cost tools.
C) tools that are not portable.
D) All of the answers listed

Question 11

Hand tools come in a variety of _____.

A) Shapes
B) Sizes
C) Functions
D) All of the above

Question 12

A power tool can be stationary, such as a(n) ______.

A) Bench grinder
B) Electric drill
C) Nail gun
D) Portable compressor

Question 13

The _______ wrench has a movable jaw that can be adjusted by turning an adjusting screw to fit any fastener within its range.

A) Flare nut
B) Pipe
C) Ratcheting box-end
D) Open-end adjustable or crescent

Question 14

Although a(n) __________ wrench often gives the best access to a fastener, if the fastener is extremely tight, this type of wrench should not be used.

A) Combination
B) Oil filter
C) Open-end
D) Ratcheting box-end

Question 15

Which of the following is a common type of wrench used in the service of automobiles?

A) Box-end wrench
B) Open-end wrench
C) Combination wrench
D) All of the above

Question 16

Technician A says that a box-end wrench is more likely to round the head of a bolt than an open-end wrench. Technician B says that 6-point sockets and wrenches have more surface area on the bolt and will hold more firmly when removing and tightening. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 17

The socket fits onto the fastener snugly and grips it on all _____ corners, providing the type of grip needed on any nut or bolt that is extremely tight.

A) Five
B) Eight
C) Six
D) Ten

Question 18

Sockets come in which of the following configurations?

A) 12 and 6 points
B) 8 and 4 points
C) Both A and B
D) None of the above

Question 19

Sockets most commonly come in which of the following configurations?

A) 12 and 6 points
B) 6 and 5 points
C) 11 and 7 Points
D) 10 and 5 points

Question 20

A foot-pound is described as the amount of twisting force applied to a shaft by a perpendicular lever __________ placed on the outer end.

A) 1 ft long with a weight of 2 lb
B) 2 ft long with a weight of 1 lb
C) 1 ft long with a weight of 1 lb
D) 2 ft long with a weight of 2 lb

Question 21

All of the following are good practices except:

A) replacing cleaning products when they lose their effectiveness.
B) discarding solvents into the sewage system immediately after use.
C) using chemical gloves when using any cleaning material.
D) wearing a respirator when using toxic cleaning chemicals.

Question 22

Technician A states that one should store commonly used tools in an easy-to-reach location. Technician B states that it is alright to leave the tools on a workbench in between jobs. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 23

The fumes from cleaning chemicals can be toxic, so wear _________ wherever you are using these products.

A) Appropriate hearing protection
B) An appropriate respirator
C) Both A and B
D) Neither A nor B

Question 24

You should never use cleaning materials near an ______ or cigarette.

A) Open door
B) Open flame
C) Open switch
D) None of the answers listed

Question 25

Inspect any electrical cables for:

A) dirt and oil.
B) chaffing or exposed wires.
C) grease.
D) All of the answers listed

Question 26

Technician A states that air tools should have oil added to their inlets once a month. Technician B states that air tools have no electrical motor built into them. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 27

A(n) ______ is capable of accurate measurements on shorter lengths, down to a millimeter or a fraction of an inch.

A) Steel rule
B) Measuring tape
C) Inside micrometer
D) Depth micrometer

Question 28

The most common type of measuring tape found in shops is a thin metal strip about ____ wide.

A) 0.5" to 1"
B) 1" to 1.5"
C) 1.5" to 2"
D) 2" to 2.5"

Question 29

A ______ is a flexible type of ruler and is a common measuring tool.

A) Yard stick
B) Measuring tape
C) Both A and B
D) None of the above

Question 30

Steel rulers most commonly come in all of the following lengths EXCEPT:

A) 12"
B) 24"
C) 36"
D) 48"

Question 31

The ______ micrometer measures the distance between the anvil and spindle, so that is where the part being measured fits.

A) Inside
B) Outside
C) Depth
D) Standard

Question 32

Technician A says the inside micrometer measures outside dimensions of an item. Technician B says the outside micrometer measures inside dimensions. Who is correct?

A) Technician A
B) Technician B
C) Both A and B
D) Neither A nor B

Question 33

Which of the following types of micrometer has the scale on the sleeve backward?

A) Depth micrometer
B) Outside micrometer
C) Inside micrometer
D) None of the above

Question 34

________ are ideal for measuring valve guides on a cylinder head for wear.

A) Telescoping gauges
B) Split ball gauges
C) Dial bore gauges
D) Vernier calipers

Question 35

Pliers are typically used for which of the following?

A) Holding material
B) Cutting material
C) Compressing material
D) All of the above

Question 36

______ are designed to cut soft metals.

A) Tin snips
B) Aviation snips
C) Bolt cutters
D) Garden shears

Question 37

The compound joints and long handles of _______ give the leverage and cutting pressure that is needed for heavy gauge materials.

A) Tin snips
B) Aviation snips
C) Bolt cutters
D) Garden shears

Question 38

Automotive fasteners may have to be measured by a ruler or _______ to identify their designation.

A) Yardstick
B) Vernier caliper
C) Meter stick
D) Measuring tape

Question 39

The full form of USCS is:

A) United States calculation system
B) United States calibration system
C) United States customary system
D) United States counting system

Question 40

Specialty tools:

A) should not be shared among technicians.
B) should have tag-out practices for regular storage.
C) should be put in the proper storage space after each use.
D) can be used for purposes they were not designed for.